• - 交流-直流(AC-DC)控制器和稳压器
• - 直流-直流(DC-DC)控制器、转换器和稳压器
• - 电压和电流管理
• - 通讯IC
• - 驱动器
• - 热管理

• - 时钟及数据分配
• - 标准逻辑

• - 放大器和比较器
• - 模拟开关
• - 数字电位计
• - 接口
• - EMI和RFI滤波器

• - EEPROM存储器
• - 非易失性只读存储器(NVRAM)
• - SRAM存储器

特性

• Expandable Five-Channel BidirectionalBuffer
• 400-kHz Fast I²C Bus
• Operating V_CC Range of 3 V to 3.6 V
• 5-V Tolerant I²C and Enable Input Pins to Support Mixed-Mode Signal Operation
• Active-High Individual Repeater Enable Inputs
• Open-Drain Input/Outputs
• Lockup-Free Operation
• Supports Arbitration and Clock Stretching Across the Repeater
• Supports Multiple Masters
• Powered-Off High-Impedance I²C Pins
• I²C Bus and SMBus Compatible
• Latchup Performance Exceeds 100 mA Per JESD 78
• ESD Protection Exceeds JESD 22
  • 2000-V Human-Body Model (A114-A)
  • 200-V Machine Model (A115-A)
  • 1000-V Charged-Device Model (C101)

All trademarks are the property of their respective owners.

DESCRIPTION/ORDERING INFORMATION

The PCA9518 is an expandable five-channel bidirectional buffer for I²C and SMBus applications. The I²C protocol requires a maximum bus capacitance of 400 pF, which is derived from the number of devices on the I²C bus and the bus length. The PCA9518 overcomes this restriction by separating and buffering the I²C data (SDA) and clock (SCL) lines into multiple groups of 400-pF segments. Any segment-to-segment transition sees only one repeater delay. Each PCA9518 can communicate with other PCA9518 hubs through a 4-wire inter-hub expansion bus. Using multiple PCA9518 parts, any width hub (in multiples of five) can be implemented using the expansion pins, with only one repeater delay and no functional degradation of the system performance.

The device is designed for 3-V to 3.6-V V_CC operation, but it has 5-V tolerant I²C and enable (EN) input pins. This feature allows for translation from 3 V to 5 V between a master and slave. The enable pin also can be used to electrically isolate a repeater segment from the I²C bus. This is useful in cases where one segment needs to run at 100 kHz while the rest of the system is at 400 kHz. If the master is running at 400 kHz, the maximum system operating frequency may be less than 400 kHz, because of the delays added by the repeater.

The output low levels for each internal buffer are approximately 0.5 V, but the input voltage of each internal buffer must be 70 mV or more below the output low level, when the output internally is driven low. This prevents a lockup condition from occurring when the input low condition is released.

A PCA9518 cluster cannot be put in series with a repeater such as the PCA9515 or another PCA9518 cluster, as the design does not allow this configuration. Multiple PCA9518 devices can be grouped with other PCA9518 devices into any size cluster using the EXPxxxx pins that allow the I²C signals to be sent or received from one PCA9518 to another PCA9518 within the cluster. Because there is no direction pin, slightly different valid low voltage levels are used to avoid lockup conditions between the input and the output of individual repeaters in the cluster. A valid low applied at the input of any of the PCA9518 devices is propagated as a buffered low, with a slightly higher value, to all enabled outputs in the PCA9518 cluster. When this buffered low is applied to another repeater or separate PCA9518 cluster (not connected via the EXPxxxx pins) in series, the second repeater or PCA9518 cluster does not recognize it as a regular low and does not propagate it as a buffered low again. For this reason, the PCA9518 should not be put in series with other repeater or PCA9518 clusters.

The PCA9518 has five multidirectional open-drain buffers designed to support the standard low-level-contention arbitration of the I²C bus. Except during arbitration or clock stretching, the PCA9518 acts like a pair of noninverting open-drain buffers, one for SDA and one for SCL.

There is an internal power-on-reset circuit (V_POR) that allows for an initial condition and the ramping of V_CC to set the internal logic.

As with the standard I²C system, pullup resistors are required on each SDAn and SCLn to provide the logic high levels on the buffered bus. The size of these pullup resistors depends on the system, but it is essential that each side of the repeater have a pullup resistor. The device is designed to work with standard-mode and fast-mode I²C devices in addition to SMBus devices. Standard-mode I²C devices only specify 3 mA in a generic I²C system where standard-mode devices and multiple masters are possible.